Chromium Corundum for Refractory Castables and Shaped Products
If you’re sourcing chromium corundum, chrome corundum or pink corundum for refractory castables and shaped products, don’t choose by colour alone. Compare Cr₂O₃ content, Al₂O₃ purity, impurity limits and particle-size distribution to ensure the right fit for refractory aggregates, fine powders and your production process.
HONREL 공급품 크롬 커런덤 for abrasive and refractory applications. Share your target specifications or current COA to find a suitable grade.
목차
Select the Material by Its Role in the Refractory Body
| Production requirement | Role of chromium corundum | What purchasing should define |
|---|---|---|
| Dense refractory castable | Coarse and intermediate particles form the load-bearing skeleton | Size fractions, sieve limits, chemistry and bulk density on the same test basis |
| Castable matrix | Fine powder fills smaller voids and joins the binder system | Powder grading, maximum oversize, Cr₂O₃, Al₂O₃, Na₂O and Fe₂O₃ |
| Pressed and fired shape | Controlled fractions support packing and green density | Particle-size distribution, pressing response and firing-trial results |
| Precast refractory shape | Aggregate and matrix must place, dry and fire as one system | Castable workability, drying behaviour, permanent linear change and final properties |
Aggregate and fine powder are not interchangeable. Replacing part of the coarse fraction with extra powder may increase water demand and reduce castable flow. Using a coarse fraction where the matrix needs powder can leave open voids and weaken bonding. Keep each fraction tied to its function.
If the order requires millimetre fractions rather than FEPA abrasive grit, state the required sieve range directly. Do not convert an F-grit number into a refractory aggregate size by assumption.
Match Cr₂O₃ to the Existing Formulation
Chromium enters the alumina crystal system and changes the behaviour of the fused grain, but more Cr₂O₃ is not automatically better. The correct level depends on the full lining design, slag or atmosphere, binder, firing schedule and thermal cycling.
HONREL’s standard PA specifications currently cover:
| HONREL grade | Cr₂O₃ | 알루미나이드 | Na₂O | Fe₂O₃ |
|---|---|---|---|---|
| Low-chromium PA | 0.20~0.45% | ≥98% | ≤0.35% | ≤0.30% |
| Medium-chromium PA | 0.45–1.00% | ≥98% | ≤0.35% | ≤0.30% |
| High-chromium PA | 1.00~2.20% | ≥98% | ≤0.35% | ≤0.30% |
The listed refractoriness is above 1850°C. HONREL also lists fine powder with Cr₂O₃ from 0.20% to 2.00%.
These figures describe HONREL’s standard PA range. They do not make the material equivalent to every high-chromia Al₂O₃–Cr₂O₃ refractory. If a formulation calls for a much higher chromium level, send the target chemistry before requesting a quotation. Matching the actual specification prevents a colour-based substitution from reaching production.
Shaped Products Must Be Checked After Pressing and Firing
For pressed bricks and other fired shapes, the raw-material COA is only the first gate. A supplier change may alter packing, die filling, green density or firing shrinkage even when the headline chemistry looks similar.
Run the candidate material through the existing production route and compare:
| Trial stage | Check before approval |
|---|---|
| Mixing | Dispersion, dusting and binder demand |
| Forming | Die filling, pressing pressure, green density and edge damage |
| Drying | Cracking, warpage and handling strength |
| Firing | Permanent linear change, apparent porosity and dimensional stability |
| Final test | Cold crushing strength, abrasion, corrosion and thermal-shock results required by the product |
Keep the binder, water or liquid addition, pressing cycle and firing curve unchanged during the comparison. This gives the raw material a fair trial and keeps the result traceable.
If you are changing sources, the related guide on switching chromium corundum suppliers explains how to compare a replacement without changing several production variables at once.
Request a Refractory Grade Match from HONREL
Send HONREL your current COA or TDS, required particle sizes, target chemistry, refractory product and regular quantity. If there is a production problem, include the symptom: poor flow, higher water demand, low green density, firing shrinkage or early lining wear.
HONREL can compare the requirement with its available PA specifications before quotation. You can also review the wider 연마재 및 내화재 범위 또는 HONREL에 문의하세요 with your purchasing specification.
